Loading...

Ultra Tile ProFlex Flexible Fibre Reinforced Tile Adhesive S2 - White

Ultra Tile ProFlex Flexible Fibre Reinforced Tile Adhesive S2 - White Flexible Fibre Reinforced Tile Adhesive S2 - White

View larger image

Ultra Tile ProFlex S2 is a single part, flexible, fibre reinforced, rapid setting adhesive for wall & floor tiles. It is specially formulated for its enhanced adhesion & flexibility making it ideal for areas where slight movement or vibration can occur.

Price: £21.95 ex VAT.  (£26.34 inc VAT)

In stock

Our quantity discounts:

Quantity  13+   25+   37+ 
Price  £18.95   £17.95   £16.95 

Ultra Tile ProFlex S2 is a single part, flexible, fibre reinforced, rapid setting adhesive for wall and floor tiles. It is specially formulated for its enhanced adhesion and flexibility making it ideal for areas where slight movement or vibration can occur.

  • Ultimate S2 flexibility
  • Rapid Setting
  • Frost-resistant


Suitable for:

  • Porcelain & Natural Stone Tiles
  • Timber Floors
  • Swimming Pools
  • Floors & Walls
  • Underfloor Heating
  • Internal & External Use
  • Available in White & Grey

 

Ultra Tile ProFlex S2 is a single part, flexible, fibre reinforced adhesive for wall and floor tiles. It is specially formulated for its enhanced adhesion and flexibility making it ideal for areas where slight movement or vibration can occur. Its unique properties make it ideal for fixing glass, porcelain, mosaic quarry, marble, terrazzo, terracotta, brick slips and ceramic tiles to most common building substrates, including concrete/sand render, screeds, brick and block work, heated subfloors, existing tiled surfaces and screwed and fixed over boarded wooden floors.

Ultra Tile ProFlex S2 is perfect for interior, exterior, wet and dry conditions, making it ideal for communal showers and swimming pools. It will take light foot traffic within 3 hours dependent upon temperature and substrate. A polymer modified adhesive for increased bond strength and enhanced performance.

Surface Preparation

The surface being adhered to must be clean, firm, dry, free of dust, dirt, oil and grease and be strong enough to support the weight of the adhesive and tiles being fixed. To encourage best adhesion to your substrate it is advisable
when applying adhesive to porous surfaces that the area is primed. Ultra Tile Prime IT FP is recommended as it will help to prevent water penetration, and increase bond strength. On non-porous surfaces use the recommended Ultra Floor primer from the Prime IT range. Ensure that the required backgrounds drying times as given in the relevant part of BS5385 are allowed to elapse prior to application of adhesive and tiling.

Wooden floors: When tiling onto timber flooring ensure that the boards are dry (i.e. conditioned to the environment in which they will be used), rigidly fixed, ventilated beneath and free from barriers to adhesion. All plywood and chipboard should have backs and edges sealed to prevent ingress of moisture and atmospheric humidity, the face to be tiled should be sealed with Ultra Tile Prime IT FP and left to dry prior to fixing. Boards should be 12mm-15mm thick
and screwed down to the joists at 300mm centres or less. In all cases the timber surface to be tiled should be adequately stable, strong and suitably rigid enough to withstand the imposing loads without deflection.

Mixing

Ultra Tile ProFlex S2 should be added slowly to clean water and mixed thoroughly to give a slump free easily worked mortar. Once mixed the mortar is immediately ready for use and has a pot life of approximately 40 minutes at 20°C. Mix only sufficient material to be used within the pot life, do not remix or re-wet. Mixing ratio: 20kg : 4.0 litres of water.

Application

Apply the adhesive to a thickness of 3mm-20mm up to 1m² at a time. On internal walls use a notched trowel, leaving solid ribs i.e. 3mm x 3mm at 6mm centres for mosaics, 5mm x 5mm at 10mm centres for wall tiles and 8mm x 8mm at 16mm centres for floor tiles. On floors and external areas, use the solid bed trowel method. Large studded tiles should be ‘buttered’. Bed the tiles in with a slight twisting action. Leave spaces between the tiles for grouting (approximately 1mm-3mm for walls and 2mm-12mm for floors). Clean off excess adhesive from the tile face and grout lines with a damp cloth before it sets.

Cleaning

Tools should be thoroughly cleaned in water to remove excess material immediately after use.

Technical Date

Packaging: 20kg bags
Standard Conformity: EN 12004 Class C2 F S2
Bed Thickness: 3mm-20mm
Coverage: 3mm bed thickness you will require 4.5kg of material per m²
Pot Life: 40 minutes depending upon temperature and substrate
Set Time: 3.5 hours dependent upon temperature and substrate
Storage: This product must be stored in unopened bags, clear of the ground in cool dry conditions and protected from excessive drafts.
Shelf Life: 12 months in above conditions.

All tiling should follow the correct British/European standard, and incorporate movement joints as specified therein.
As with all raw materials, colour variation may occur. Please note that this does not affect the consistency of characteristics of the enclosed product.

 

Secured By Card Save